誰能幫我翻譯下這片文章？翻譯的好的在追加100分！??！
-
Experimental Method All experiments were carried out in a high-pressure CO2 apparatus (Speed-SFE from Applied Separations) (see Figure 1) with a 300-mL extractor designed for a maximum pressure of 690 bar and a maximum temperature of 2... Experimental Method All experiments were carried out in a high-pressure CO2 apparatus (Speed-SFE from Applied Separations) (see Figure 1) with a 300-mL extractor designed for a maximum pressure of 690 bar and a maximum temperature of 250 °C. The volume of the extractor had to be reduced to 50 mL by a metallic cylinder， which tightens to the extractor wall， because as preliminary tests showed the equilibrium cell has to be completely filled with material. Otherwise， diffusion is the limiting factor and time for reaching equilibrium was too long. The extraction vessel was filled with compressed CO2 by an air-driven pump at closed outlet valves and under static conditions， which means desired pressure and temperature; the cell was incubated for 15 h， maintaining these conditions to reach equilibrium. In preliminary experiments the equilibrium time of 15 h was determined to reach equilibrium. CO2 Sampling. At equilibrium a CO2 phase sample is taken by opening the outlet valve and expanding a certain amount of CO2-substance mixture into a cooling trap filled with toluene， which has the highest solubility for the measured substances under atmospheric conditions. The pure gaseous CO2 passes a rotameter， showing the actual flow rate， and a gas flowmeter for determining the expanded CO2 amount. The content of the cooling trap was filled up with toluene to 30 mL and analyzed by a gas chromatographic method using an electron capture detector (GC-ECD). With the mass of expanded CO2 and composition of the cooling trap solubility at a certain pressure and temperature was calculated. Sampling was repeated four times at a given pressure and temperature and the standard deviation was lower than 5%. Gas Chromatographic Method. The tolueneflame retardant mixture of CO2 sampling was analyzed in a gas chromatograph (HP 5890 Serie II) with an ECD using a capillary column (type HP-1， 12 m 0.2 mm 0.2 ím). The injector temperature was held constant at 290 °C and the detector temperature at 300 °C. The oven temperature was held constant at 290 °C. Calibration with different amounts of HBCD and TBBA in toluene has been done before determining the linear range of calibration line and retention time of substances 展開
全部評論(1條)
-
- 長的帥逗人愛 2008-06-05 00:00:00
- 實驗方法所有實驗進行了在高壓力， CO2的器具（速度從應用超臨界流體萃取分離） （見圖1 ）與300毫升萃取器設計的Z高壓力690酒吧和一的Z高溫度250 ° C時量的萃取不得不減少到五十○毫升由一個金屬圓筒，收緊向萃取墻，因?yàn)槌醪綔y(cè)試結果顯示，平衡細胞已被完全填滿與材料。否則，擴散是限制因素和時間達成平衡是過長。提取船只充滿了壓縮的CO2由一個空氣驅動泵在這些已關閉的出口閥門和靜態條件下，這意味著理想的壓力和溫度;細胞培養15小時，保持這些條件，以達到平衡。在初步的實驗平衡的時間為15小時決心達到平衡。二氧化碳采樣。在平衡二氧化碳相調查樣本，所采取的開放，出口閥和擴大一定數額的二氧化碳物質的混合物成為一個冷卻的陷阱，充滿甲苯，具有Z高的溶解度為衡量物質常壓下的條件。純氣體的CO2通過浮子，顯示的實際流速，和氣體流量計的決定擴大二氧化碳的金額。內容冷卻的陷阱，是填補了與甲苯30毫升和分析，由氣相色譜法使用電子捕獲檢測器（氣相色譜-幼兒發展） 。與大規模的擴大， CO2和組成冷卻陷阱的溶解度在一定溫度和壓力計算。采樣重復4次在某一特定壓力和溫度和標準偏差低于5 ％ 氣相色譜法。該tolueneflame阻燃混合物CO2的采樣，分析了在一個氣相色譜儀（惠普5890系列二）與一幼兒發展使用毛細管柱（類型的HP - 1 ， 12米0.2毫米0.2 ím ） 。噴油器溫度舉行了不斷在290 ° C和檢測器溫度在300 ° C時校準與不同數量的hbcd和tbba在甲苯中已做了，然后才決定的線性范圍為校準線和保留時間的物質. 我一小段一小段的翻譯的，555555，累死餓了..
-
贊(14)
回復(0)
登錄或新用戶注冊
- 微信登錄
- 密碼登錄
- 短信登錄
請用手機微信掃描下方二維碼
快速登錄或注冊新賬號
微信掃碼，手機電腦聯動
注冊登錄即表示同意《儀器網服務條款》和《隱私協議》
熱門問答
- 誰能幫我翻譯下這片文章？翻譯的好的在追加100分?。?！
- Experimental Method All experiments were carried out in a high-pressure CO2 apparatus (Speed-SFE from Applied Separations) (see Figure 1) with a 300-mL extractor designed for a maximum pressure of 690 bar and a maximum temperature of 2... Experimental Method All experiments were carried out in a high-pressure CO2 apparatus (Speed-SFE from Applied Separations) (see Figure 1) with a 300-mL extractor designed for a maximum pressure of 690 bar and a maximum temperature of 250 °C. The volume of the extractor had to be reduced to 50 mL by a metallic cylinder， which tightens to the extractor wall， because as preliminary tests showed the equilibrium cell has to be completely filled with material. Otherwise， diffusion is the limiting factor and time for reaching equilibrium was too long. The extraction vessel was filled with compressed CO2 by an air-driven pump at closed outlet valves and under static conditions， which means desired pressure and temperature; the cell was incubated for 15 h， maintaining these conditions to reach equilibrium. In preliminary experiments the equilibrium time of 15 h was determined to reach equilibrium. CO2 Sampling. At equilibrium a CO2 phase sample is taken by opening the outlet valve and expanding a certain amount of CO2-substance mixture into a cooling trap filled with toluene， which has the highest solubility for the measured substances under atmospheric conditions. The pure gaseous CO2 passes a rotameter， showing the actual flow rate， and a gas flowmeter for determining the expanded CO2 amount. The content of the cooling trap was filled up with toluene to 30 mL and analyzed by a gas chromatographic method using an electron capture detector (GC-ECD). With the mass of expanded CO2 and composition of the cooling trap solubility at a certain pressure and temperature was calculated. Sampling was repeated four times at a given pressure and temperature and the standard deviation was lower than 5%. Gas Chromatographic Method. The tolueneflame retardant mixture of CO2 sampling was analyzed in a gas chromatograph (HP 5890 Serie II) with an ECD using a capillary column (type HP-1， 12 m 0.2 mm 0.2 ím). The injector temperature was held constant at 290 °C and the detector temperature at 300 °C. The oven temperature was held constant at 290 °C. Calibration with different amounts of HBCD and TBBA in toluene has been done before determining the linear range of calibration line and retention time of substances 展開
2008-06-04 17:17:07
587
1
- 誰能幫我翻譯下費希爾調節閥的名牌
2016-10-01 02:11:08
398
2
- 麻煩幫我翻譯以下文章(生物專業英語)
- The most common means of agitation of liquid media is by placing the culture vessels on a drum(for test tubes)or a disk(for flasks)slowly rotating around a near horizontal axis. This assures good aeration of the liquid cultures with little... The most common means of agitation of liquid media is by placing the culture vessels on a drum(for test tubes)or a disk(for flasks)slowly rotating around a near horizontal axis. This assures good aeration of the liquid cultures with little mechanical damage to the cells.Agitation can also be achieved by placing culture flasks on reciprocating or gyrotory platform shakers.Gyrotoy (horizontal rotary orbit)shakers are preferred over reciprocating (horizontal linear motion)ones for a variety of reasons .The performance of the gyrotory shaker is determined by the speed of agitation and angle position of the flasks，with optimal aeration occurring in flasks tilted about 45° from the vertical.A new shaker design is the "tapping" motion shaker in which the culture is agitated by a magnetic bar moving up and down.This vertical movement of the bar is less injurious to cells than rotary movement of the bar at the bottom of the flask used in some conventional culture systems. 展開
2008-05-30 20:14:03
743
2
- ？？？？？誰能幫我翻譯幾個英文——激光雷達？？？？？
- 關于激光雷達的論文 1、LO 2、header board 3、inductive beams
2008-06-17 10:12:22
646
2
- 急！??！誰能幫我翻譯一下？萬分感謝！
- Definitions: APQP ASDE BOM EPR ESWP Advanced Product Quality Planning Advanced Supplier Development Engineer Bill of Material Early Program Review Early Sourcing Work Plan. A report including Commodity Classification (Metals，... Definitions: APQP ASDE BOM EPR ESWP Advanced Product Quality Planning Advanced Supplier Development Engineer Bill of Material Early Program Review Early Sourcing Work Plan. A report including Commodity Classification (Metals， Non- Metals， Electrical/electronics)， source-required dates， cost targets， and production tooling kick-off required dates for all purchased components. The document representing the European ESWP is On Track， the NA is PPTM. Procedure # VP-014 LRR On Track PPAP PPTM PSW RPC SDE SOP SPE VPDS vTPS Procedure: Launch Readiness Review European version of the Early Sourcing Work Plan (ESWP) Production Part Approval Process Purchased Parts Tracking Matrix (ESWP/PPTM): The North American version of the ESWP. The ESWP/PPTM is an Access Database maintained by NA Program Purchasing (vTPS) to capture all Forward Model Purchase Component information. Part Submission Warrant Regional Program Coordinator is a function within SPE in Europe and South America. Supplier Development Engineer Start Of Production (sometimes referred to as Job 1) Supplier Performance Engineer (combined ASD and SD Engineer) Visteon Product Development System ， PD/Program Management Gateway process used to manage the successful launch of new model programs. The North American data storage system which holds all PPTM/ESWP data. vTPS is an Access Database Responsibility: Process Map/Flowchart (1) Lead: RPC/SPE (EU & SA) (1) Lead – ASDE (NA & Asia) Conduct High Impact Assessment assign ASD / SP engineer on formal W/support from: Program sourcing and / or change of BOM. Buyer PD Engineer Program Manager – All Regions (2) Notes/Deliverables (1) Inputs: ? ESWP or local equivalent from VP-040 Project Supply Management Outputs: ? High Impact Assessment Form (VF-014a or local equivalent) Notes: ? Conduct High Impact Assessment and record results per local work instructions (2) Lead: RPC/SPE (EU & SA) Lead – ASDE (NA & Asia) W/support from: Program Buyer - All Regions， Buyer - All Regions (3) Lead: Program Buyer (NA & EU & Asia) Lead: RPC/SPE (SA) (4) No No (2) Is the part High Impact? (3) Can Supplier achieve PSW Timing? Yes Go to Step # 5. Yes Go to Step # 8. (3) Notes: ? Record PPAP status on local tracking system. (4) Hard Copies of This Document are Uncontrolled Page 2 of 4 (4) Acceptable risk to Yes 展開
2008-07-24 01:42:57
635
1
- 翻譯翻譯，請高手幫我翻譯一下這個說明
- Followthesysteminstallationinstructionscarefullyandinthespecifiedorder.ThesoftwaremustbeinstalledonthecomputerbeforeconnectingtheUSBcable.2.1FacilitiesRequirementsFacilit... Follow the system installation instructions carefully and in the specified order. The software must be installed on the computer before connecting the USB cable. 2.1 Facilities Requirements Facilities requirements for the alpha-SE system are listed in Table 2-1 and the system dimensions are given in Fig. 2-1. As shown in Fig. 2-2， the alpha-SE tool requires a clear work area of 20 by 18 inches (500 by 460 mm)， excluding the operator computer. 2.2 Unpacking the Hardware Opening the Shipping Container Move the alpha-SE shipping container to the area where the tool will be installed. Open the container and remove the top and side pieces of packing foam. Carefully remove all smaller components from the shipping container， verifying that you received all components， as shown in Fig. 2-3. Finally， remove the alpha-SE ellipsometer and position it on your clear 20” by 18” (510 by 460 mm) workspace. Caution: The alpha-SE ellipsometer without sample chuck weighs approximately 37 lbs. (16 kg.). Please find an assistant to lift the alpha-SE unit out of the shipping carton and on to clear work surface. 展開
2008-06-22 06:30:36
888
4
- 急求幫我翻譯一段電力專業英語文章啊！！
- What's therole of the Supercapacitor? The supercapacitor resembles a regular capacitorwith the exception that it offers very high capacitance in a small package.Energy storage is by means of static charge rather than of an electro-che... What's therole of the Supercapacitor? The supercapacitor resembles a regular capacitorwith the exception that it offers very high capacitance in a small package.Energy storage is by means of static charge rather than of an electro-chemicalprocess that is inherent to the battery. Applying a voltage differential on thepositive and negative plates charges the supercapacitor. This concept issimilar to an electrical charge that builds up when walking on a carpet. Thesupercapacitor concept has been around for a number of years. Newer designsallow higher capacities in a smaller size. Whereas a regular capacitor consists ofconductive foils and a dry separator， the supercapacitor crosses into batterytechnology by using special electrodes and some electrolyte. There are threetypes of electrode materials suitable for the supercapacitor. They are: highsurface area activated carbons， metal oxide and conducting polymers. The highsurface electrode material， also called Double Layer Capacitor (DLC)， is leastcostly to manufacture and is the most common. It stores the energy in thedouble layer formed near the carbon electrode surface. 展開
2013-06-11 09:00:02
513
3
- LABVIEW 虛擬儀器 高手幫我翻譯下好嗎?
- 4.VIRTUALINSTRUMENTAfoundationofthecontrolsystemdesignistheconceptofvirtualinstruments.Intraditionalobservatorysystemdesign，instrumentsaretypicallyconsideredentitieswhose... 4. VIRTUAL INSTRUMENT A foundation of the control system design is the concept of virtual instruments. In traditional observatory system design， instruments are typically considered entities whose design and components are fixed well in advance of actual use of the instrument. The approach works quite well when the role of the instrument is well understood with respect to the experiments it is to be used for. It also fits well with a system design where the instruments must be mounted on the telescope (e.g. mounting at the Cassegrain focus)， or exposed to the external environment - since the instrument is static， it can be more easily enclosed. However， this approach has some drawbacks in a laboratory style environment such as that provided by the ATST multiple-bench coude lab. In particular， providing the flexibility to explore new experiments results in a significant effort to adapt existing instruments to meet the requirements of the new experiment. The Virtual Instrument Model has been developed to address this issue， by abstracting the concept of an instrument from the specifics of the components used within that instrument. This allows the configuration of an instrument to be quickly adapted to meet the changes required by different experiments or changes to the laboratory environment. It should be noted that the virtual instrument is not a revolutionary concept but rather is the formalization of ideas often used in laboratory style experimentation. In the virtual instrument model， it is the experiment that drives the virtual instrument's 'design'. 4.1. EXPERIMENTS AND INSTRUMENTS Experiments are the heart of ATST operations and the control system is designed with this in mind. A laboratory style environment provides flexible support to carry out Experiments that are likely not understood or defined at the time the laboratory itself is designed. An Experiment undertaken at the ATST requires a Virtual Instrument. 不要機器翻譯的 要人工的 謝謝大家 展開
2008-01-28 20:42:17
449
1
- 誰能幫我翻譯一下這段英文文獻啊
- Fig. 1 shows that diamond particles are dispersed in the copper matrix. Since the diamond particles are easy to be stripped off during mechanical polishing， small pits are left on the surface of samples. When the samples were analyzed b... Fig. 1 shows that diamond particles are dispersed in the copper matrix. Since the diamond particles are easy to be stripped off during mechanical polishing， small pits are left on the surface of samples. When the samples were analyzed by electron probe for carbon， the particles displayed high carbon peaks， as shown in Fig. 2. Fig. 3 exhibits the analyzed result for extracted product of the copper–diamond composite by X-ray diffraction (XRD) analysis. It is shown that three dif- fraction peaks exist， shown as A， B and C， respectively. The interplanar distances corresponding to the three peaks and standard ones for diamond are compared in Table 1. The measured values of the interplanar distances are in good agreement with the standard ones， demon- strating that the extracted product should be the carbon in diamond state. Fig. 4(a) gives a TEM micrograph showing distribution and morphology of diamond particles (indicated as A， B， and C) in the copper–diamond composite. The calibration of interplanar distance for diffraction rings in Fig. 4(b) was given in Table 2. Compared to Table 1， it is also demon- strated that the calibrated interplanar distances for the diffraction rings conform to the standard ones of diamond. Therefore， it is believed that the graphitization of diamond particles hardly occurs after sintering at 1150–1220 K in the copper–diamond composite. Although diamond is a metastable allotropic modifica- tion of carbon， the graphitization of diamond particles in the copper–diamond composite did not occur， or the degree of graphitization was too small to be found. It is believed that the beginning temperature of graphi- tization would be associated with the purity of diamond powders. The impurities such as some metallic elements reduce the beginning temperature of diamond graphitiza- tion. When diamond is fabricated by the static synthesis method， Fe and Ni are often used as catalysts and are present in diamond as impurities to decrease the beginning temperature of graphitization [6]. It is understandable that both for the graphitization and its reverse reactions， their activation energies can be decreased by catalytic agents. Compared with the diamond fabricated by static synthesis， the diamond powders prepared by explosion method do not contain metallic impurities， thus leading to an obvious increase in the beginning temperature of graphitization. Hence， the detonation synthetic diamond might be more resistant to graphitization and probably suitable for the electric contact materials. 展開
2011-03-22 08:43:56
449
2
- 誰能幫我翻譯 一篇和材料有關系的論文?
- 題目名字叫Microwave-AssistedSimpleSyntheseisofSubstituted4-QuinoloneDerivatives... 題目名字 叫 Microwave-Assisted Simple Syntheseis of Substituted 4-Quinolone Derivatives 展開
2011-11-16 10:23:14
410
2
- 麻煩英文好的幫忙翻譯下~~~~
- 虛擬儀器技術與NI的優勢及發展趨勢展望摘要：本文介紹了虛擬儀器的概念及發展。從虛擬儀器的組成，NI的優勢及21世紀發展趨勢的展望進行了詳細的介紹。... 虛擬儀器技術與NI的優勢及發展趨勢展望 摘要：本文介紹了虛擬儀器的概念及發展。從虛擬儀器的組成，NI的優勢及21世紀發展趨勢的展望進行了詳細的介紹。 展開
2008-11-12 05:08:51
400
2
- 誰幫我翻譯一下
- LabVIEWTM(LaboratoryVirtualInstrumentEngineeringWorkbench)isapowerfulinstrumentationandanalysisprogramminglanguageforPCsrunningMicrosoftWindows，SunSPARCstations，AppleMaci... LabVIEWTM (Laboratory Virtual Instrument Engineering Workbench) is a powerful instrumentation and analysis programming language for PCs running Microsoft Windows， Sun SPARCstations， Apple Macintosh computers， Concurrent PowerMax， and HP-UX workstations. LabVIEW departs from the sequential nature of traditional programming languages and features a graphical programming environment and all the tools needed for data acquisition， analysis， and presentation. With this graphical programming language， called “G，” you can program in a block diagram notation， the natural design notation of scientists and engineers. After you create a block diagram program， LabVIEW compiles it into machine code. LabVIEW integrates data acquisition， analysis， and presentation in one system. For acquiring data and controlling instruments， LabVIEW supports RS-232/422， IEEE 488 (GPIB)， and VXI， including Virtual Instrument Software Architecture (VISA) functions， as well as plug-in data acquisition (DAQ) boards. An instrument library with drivers for hundreds of instruments simplifies instrument control applications. For analyzing data， the extensive Analysis library contains functions for signal generation， signal processing， filters， windows， statistics， regression， linear algebra， and array arithmetic. Because LabVIEW is graphical in nature， it is inherently a data presentation package. LabVIEW can generate charts， graphs， and customized， user-defined graphics. 盡量翻的好一點，謝謝 能不能對GOOGLE自動翻譯過的稍加修改下 展開
2008-03-24 08:56:44
573
4
- 幫我翻譯一段話，謝謝
- AretheurbansoilsofGuangzhoupolluted?Inareviewofheavymetalpollutionofsoilsinchina，chenetal.(1999)suggestedthat“Heavy-metalsoilpolltionisdefinedasthephenomenawheretheheavy... Are the urban soils of Guangzhou polluted? In a review of heavy metal pollution of soils in china，chen et al.(1999) suggested that“Heavy-metal soil polltion is defined as the phenomena where the heavy-metal content in soils exceeds natural background levels and causes ecological destruction and deterioration of environmental quality” Table 6 compares the Guangzhou date with some background date and also some critical and trigger limits derived from the Netherlands and U.K. It can be seen from Table 6 that all top soil heavy metals，with the exception of Ni in the Park，are above the average value for Guangdong province. They also，again with the exception on Ni in the park，exceed the values for samples from Hainan Island，which affords a“clean”baseline data sea for the region. what is also of interest is that if the rations of heavy metal content for roadside sites in Guangzhou are compared to the Hainan data in from of a ratio then ratios of 3.09，1.04，4.16，1.84 and 1.59 are obtained for Cu，Ni，Zi，Pb and Cu respectively. With the exception of the 4.16 for Zn they are not dissimilar to rations of roadside to park top soil reported previously for Guangzhou. This suggests that the roadside to park comparison for soils in Guangzhou may pick up enhancement of heavy metals associated with vehicular traffic. 展開
2009-06-21 09:02:15
326
1
- 幫我翻譯下8種有機錫化物的名字！ 謝謝 ！
- 幫我翻譯下8種有機錫化物的名字！謝謝！Monobutyltin/Monooctyltin/Dibutyltin/Dioctytlin/Triphenyltin/Triphenyltin/Tricyclohexyltin/Tetrabutyltin.... 幫我翻譯下8種有機錫化物的名字！ 謝謝 ！Monobutyltin/Monooctyltin/Dibutyltin/ Dioctytlin/Triphenyltin/Triphenyltin/Tricyclohexyltin/Tetrabutyltin. 展開
2009-07-21 06:25:05
636
1
- 求翻譯 關于光催化劑的科研文章
- 求 對下段文字的英語翻譯： 本研究主要采用改良的溶膠凝-膠法制備納米級的二氧化鈦光催化劑，有別于一般制備二氧化鈦的溶膠凝膠過程，實驗利用冰醋酸和正丁醇發生酯化反應產生的水與鈦酸丁酯進行水解反應。另外冰乙酸具有螯合物的功能，可以降低金屬醇鹽的高... 求 對下段文字的英語翻譯： 本研究主要采用改良的溶膠凝-膠法制備納米級的二氧化鈦光催化劑，有別于一般制備二氧化鈦的溶膠凝膠過程，實驗利用冰醋酸和正丁醇發生酯化反應產生的水與鈦酸丁酯進行水解反應。另外冰乙酸具有螯合物的功能，可以降低金屬醇鹽的高水解速度，避免快速沉淀的產生而制備出均相二氧化鈦溶膠。溶膠經干燥、煅燒得納米二氧化鈦粉體。 同時通過負載金屬元素Fe和非金屬元素N對二氧化鈦催化劑表面進行改性，提高其催化活性，并對其催化活性進行XRD、TG/DTG/DSC、BET等各項表征，選出催化效果較佳的光催化材料進行CO2光催化還原反應，把CO2轉化為有用的有機物甲醇，并從理論上探索CO2光催化反應機理。 展開
2010-06-04 05:01:48
540
2
- 誰幫我翻譯一下，謝謝
- ···until TLC analysis indicated the absence of dipolarophile.
2008-10-25 07:34:06
441
2
- 急求英譯漢高手（詞霸翻譯不加分）翻譯好了 追加50
- http://hi.baidu.com/lyl464797826/blog/item/0c12e646eca6ee3287947334.html
2010-06-19 21:53:22
518
1
4月突出貢獻榜
推薦主頁
最新話題
滬公網安備 31011502008050號
參與評論
登錄后參與評論