鉗形電流表精度±(3.0%+5)中，+5什么意思？

獅子魯昭 2018-01-26 08:14:39 597 瀏覽

參與評論

評論

登錄后參與評論

全部評論(1條)

mixdulexs 2018-01-27 00:00:00

數字表的誤差表示方法，誤差比量程的3%還要多出“5”個末位字。例如3位半顯示的200.0A的檔位，誤差可以達到200X3%+0.5=6.0+0.5=6.。

贊(1)

回復(0)

評論

評論
登錄后參與評論

登錄或新用戶注冊

微信登錄
密碼登錄
短信登錄

請用手機微信掃描下方二維碼
快速登錄或注冊新賬號

微信掃碼，手機電腦聯動

注冊登錄即表示同意《儀器網服務條款》和《隱私協議》

熱門問答

鉗形電流表精度±(3.0%+5)中，+5什么意思？:

全站儀精度±2″/5″ 什么意思 0.4？:

乳膠管5*9什么意思:

三相電流表500/5什么意思:

色度儀±5% 10 pcu什么意思:

電流表 6L2-A 250/5 中250/5是什么意思？:

汽車轉速表，指針5表示什么意思？:

紅外測溫儀參數中的紅外測溫精度正負1. 5攝氏度是啥意思？:

pe等徑三通dn90×5表示什么意思:

請問鉗形表交直流電流精度±2.5%±5是什么意思？:

LED顯示屏室內3.0單色 3.0什么意思:

鉗形電流表的中a ac什么意思:

高分英譯中 (5): CIPTankFill–theCIPtankisfilledfromoneoftheunitsinoperation.CIPTankHeating–foracidCIPs，thewaterintheCIPtankisheatedto40°C.Backwash-Theskidisbackwashedtoremoveexcesssoli... CIP Tank Fill – the CIP tank is filled from one of the units in operation. CIP Tank Heating – for acid CIPs， the water in the CIP tank is heated to 40 °C. Backwash - The skid is backwashed to remove excess solids and maximize the chemical cleaning efficiency. The backwash waste is drained to the regular waste outlet. Hot water Fill - The skid is filled with water from the CIP tank. Filtrate Recirculation and Chemical Dosing - The CIP transfer/recirculation pump starts to recirculate the water to the skid in a closed loop. The skid is fully isolated from the rest of the system， typically by block and bleed systems. The acid or chlorine (sodium hypochlorite) is added in the loop at the beginning of the recirculation sequence until the appropriate quantity of cleaning chemical is added. Filtrate Recirculation – The cleaning solution is recirculated through the filtrate side of the membrane array. This step is similar to filtration. Soak/Aeration - The modules are left to soak for a preset time. With an acid clean， repeated aeration steps can be used to improve cleaning efficiency. Draindown - The cleaning solution is drained away from the skid to drain or to the neutralization system if the system incorporates one. Rinse Backwash - The skid is refilled with feed water and backwashed to remove residual chemical. All rinse water is directed to drain or the neutralization system. Filtration to Waste – The unit is put into filtration but the filtrate with chemical residue is sent to drain or the neutralization system. The pH and ORP meters are used to verify that the skids have been rinsed to the point where the filtrate has no chemical cleaning residue. The unit can then be put back into filtration or standby. Pressure Decay Test (PDT) The integrity test procedure is similar to that used on all of the other Memcor systems. The principal process steps include draining down the lumen of the fibers， pressurizing the inside of the module fibers with integrity air while the upper backwash waste outlet valve is open to atmospheric pressure， shutting down the air supply and monitoring the pressure over time using the filtrate pressure transmitter supplied with each unit. The PDT result is logged on the SCADA system and displayed on the SCADA computer as well as the optional local HMI. This result is used to calculate the Log Removal Value (LRV)， which confirms integrity of the system. Each Memcor CP unit is tested at regular time interval adjustable by the operator. The time interval is set at 24 hours by default. 展開